• Enables safe make up and break out of connections
• Light weight
• Easy to operate
• Bi-directional Hydraulic Cylinder
• Hand Pump operated; no other power source required.
• Easy to change replaceable dies.
• Adjustable to suit a range of diameters.

Applications

• Make-up/Break-out of Tool Joints
• Make-up/Break-out of service connections

Operation

The WellEnTech SafeTorqCT™ consists of two separate clamping components connected via a Bi-directional Hydraulic Cylinder. The clamps are opened and attached to either side of a connection. The clamps are then tightened, and the hoses fitted to the Hydraulic Cylinder. The application of hydraulic pressure produces a torque which can be used to make-up or break a connection under fully monitored and safe conditions.  

Download datasheet

The post SafeTorqCT™ appeared first on WellEnTech.

• Jar testing
• Shear testing
• Tensile or compressive testing

Download datasheet

The post Jar Tester appeared first on WellEnTech.

• Compact design.
• Easy to install/remove
• Fits all sizes of WECO hammer lug Union
• Stainless Steel construction

Applications

• Any fluid pumping operations

Operation

The Surface Filter is inserted into the WECO hammer lug union without the need for any specialized installation tools. The Hammer Lug Union can then be made up as normal and operations can proceed. The elongated filter design maximises the amount of debris which can be collected. To swap out the filter or remove it, the Hammer Lug Union is broken out and the filter pulled out of the treating iron. Flats and a drilled hole are included to ease disassembly.

Download datasheet

The post Surface Filter appeared first on WellEnTech.

• Thru’ bore to accommodate wireline
• No specialist assembly tools required
• Interchangeable reamers and coil inserts
• Compatible for a range of sizes and wall thicknesses

Applications

• Coiled Tubing Preparation
• Can be used on a range of Coiled Tubing diameters and wall thicknesses
• Suitable for use with both Roll-on and Dimple-on Connectors

Operation

The WellEnTech CT Reamer Assembly is fitted with a suitable Coil Insert (to match the tubing OD) and a Reamer (to suit the tubing ID). The Threaded Sleeve is backed off and the assembly is attached to the Coiled Tubing with a set screw which sits through the Coil Insert. The Reamer Mandrel of the tool can then be rotated using the ergonomically designed handles and the Threaded Sleeve gradually made up until the bead running up the ID of the tubing has been removed. A Bevel Cutter is available for the tool which replaces the Reamer in order to cut an internal chamfer in the end of the tubing.

Download datasheet

The post CT Reamer Assembly appeared first on WellEnTech.

• Forged Steel Body
• Spring Pressure System
• Broad Support Rollers
• Roll-on and Cutter wheels available
• Quick and easy wheel change out
• Compatible for a range of Tubing diameters

Applications

• Roll-on of Coiled Tubing to Roll-On Connector.
• Suitable for all grades of coiled tubing.
• Cutting of Coiled Tubing

Operation

Having dressed the Coiled Tubing with the WellEnTech CT Reamer Assembly (Ref Data Sheet DS-590). The Roll-On Connector is placed beside the section of Coiled Tubing it is to be fitted to and the position of the roll-on grooves are marked onto the tubing. The Connector is then inserted into the Coiled Tubing and the Crimper Tool is fitted and aligned with the marks on the tubing. The Crimper Tool Handle is rotated to clamp it onto the tubing. The whole Crimper tool is rotated and the handle is further tightened. This process is repeated until the roll-on groove is formed in each of the three locations.

Download datasheet

The post Crimper Tool appeared first on WellEnTech.

• Compact design
• Standard hex head sizes
• Compatible for a range of coil wall thicknesses

Applications

• For dimpling coiled tubing onto Dimple-on Coil Connectors*
• Suitable for all grades of coiled tubing

* Dimple-on Coil Connectors, Pressure Test Subs, Pull Test Subs and CT Reamer Assemblies are all available from Wellentech.

Operation

The WellEnTech Manual Dimple Jig Assembly consists of two halves which are bolted together. There are two grub screws, one for orientation on the Connector and one for securing the jig onto the Coiled Tubing. Each of the Dimple Screws are then tightened to a specific torque value, which results in the forming of dimples onto the Dimple-on Coil Connector. A pull test will confirm the connector has been fitted correctly and a pressure test will verify that a seal has been maintained. It is recommended that the Coiled Tubing is prepared with a WellEnTech CT Reamer Assembly* prior to installing the Connector.

Download datasheet

The post Manual Dimple Jig Assembly appeared first on WellEnTech.

• Compact design
• Robust construction
• Compatible for a range of coil wall thicknesses
• Easy to maintain and redress

Applications

• For dimpling Coiled Tubing for External Dimple Connectors*
• Suitable for all grades of Coiled Tubing

* Dimple-on Coil Connectors, Pressure Test Subs, Pull Test Subs and CT Reamer Assemblies are all available from Wellentech.

Operation

The WellEnTech Hydraulic Dimple System can be used with either a hand pump or hydraulic power pack. Having selected a suitable Dimple Jig to suit the Coiled Tubing to be dimpled, it is then fitted to the Connector and the prepared Coiled Tubing and secured in place. There are two grub screws, one for orientation on the Connector and one for securing the jig onto the Coiled Tubing. The Hydraulic Dimple Assembly can then be placed onto the Dimple Jig and is automatically orientated by flats. The application of hydraulic pressure results in the forming of dimples onto the Dimple-on Coil Connector. This process is repeated until all the dimples are formed. A pull test will confirm the Connector has been fitted correctly and a pressure test will verify that a seal has been maintained. It is recommended that the Coiled Tubing is prepared with a WellEnTech CT Reamer Assembly* prior to installing the Connector.

Download datasheet

The post Hydraulic Dimple System appeared first on WellEnTech.

• Compact design
• Integral Slide Hammer and Sub
• Compatible for a range of coil wall thicknesses
• Easy to maintain and redress

Applications

• For dimpling Coiled Tubing for External Dimple Connectors*
• Suitable for all grades of Coiled Tubing

* External Dimple Connectors, Pressure Test Subs and Pull Test Subs are all available from Wellentech.

Operation

The WellEnTech Hydraulic External Dimple System should be used with a hydraulic hand pump. Having selected a suitable System to suit the Coiled Tubing to be dimpled, it is then fitted to the Coiled Tubing and secured in place with a Socket Set Screws. The application of hydraulic pressure results in the forming of dimples onto the Coiled Tubing. The screws are backed off and the Dimple System rotated 90°.The dimpling process is repeated until all the dimples are formed. A pull test will confirm the Connector has been fitted correctly and a pressure test will verify that a seal has been maintained. The WellEnTech Hydraulic External Dimple System is supplied with a Slide Hammer and Threaded Sub to assist with the fitting and removal of the External Dimple Connector.

Download datasheet

The post Hydraulic External Dimple System appeared first on WellEnTech.

• Compact design
• Standard hex head sizes
• Compatible for a range of coil wall thicknesses

Applications

• For dimpling coiled tubing to suit External Dimple Connectors*
• Suitable for all grades of coiled tubing

* External Dimple Connectors, Pressure Test Subs and Pull Test Subs are all available from WellEnTech.

Operation

The WellEnTech External Dimple Jig Assembly consists of two three distinct components, the Dimple Sub, the Hammer and the Removal Sub. The Dimple Sub creates the Dimples on the Coiled Tubing, this is achieved by tightening hardened Dimple Screws which produce a uniform dimple of the exact size to suit the External Dimple Connector. The Hammer is used to knock on and off the Dimple Sub, Knock on the External Dimple Connector or also remove the Connector. The Removal Sub provided a means of holding onto the Connector during fitting and removal. A pull test will confirm the External Dimple Connector has been fitted correctly and a pressure test will verify that a seal has been maintained.

Download datasheet

The post External Dimple Jig Assembly appeared first on WellEnTech.

• Compact lightweight design
• 2 tonne safe working load
• Compatible for use with tools up to 3-1/8”OD
• Easy to maintain and redress.
• Interchangeable Top and Base Plates

Applications

• Supporting and manipulation of BHA
• Assisting with connection make-up
• QIKTech™ Stabbing and make-up

Operation

The WellEnTech Hydraulic C-Plate is placed in the desired location. The Hydraulic Hand Pump and hose are then connected to the Female Coupler on the hydraulic C-Plate. With a suitable Tool Clamp fitted to the Lower half of the tool String, the BHA can be hung off from the top plate. Slowly apply pressure to raise the top plate to raise the lower half of the tool string closer to the upper half of the tool String enabling both halves of the BHA to be made up as per operational procedures. To remove, simply bleed off the hydraulic pressure to allow Hydraulic C-Plate to retract.

Download datasheet

The post Hydraulic C-Plate appeared first on WellEnTech.